We disassemble the macbook pro. Disassembling an Apple MacBook Pro laptop with a Touch Bar showed that it is better to be very careful with the device. The effect of replacing thermal paste, battery and some tips

The MacBook Pro's aluminum unibody design is a technical achievement. Its unibody body is crafted from a single piece of aluminum using precision machining. The result is a laptop like no other: thin, light, sleek and sleek.

1. Let's start disassembling the Macbook Pro by removing the back battery cover.

2. Unscrew the holder screw hard drive and 4 screws of the fastener itself. Replacing the HDD yourself in unibody models is much easier than in previous Macbook Pro models. The laptop has standard SATA HDD.

3. Now remove the bottom cover of the laptop. To do this, unscrew 8 screws. The MacBook Pro is disassembled in the same way as the old PowerBook G4 Titanium and in a very similar way to the MacBook Air: remove the bottom cover and gain access to all components of the computer. The wires go from different parts to the board more neatly than in the new Macbook, because there is more space - there is room to roam.

5. Now we take out two 1GB DIMMs. 1066 MHz DDR3 SDRAM chips. Apple says the computer supports up to 4GB of RAM, but we've learned that the Montevina chipset allows for up to 8GB of RAM. You can upgrade your RAM without any problems yourself, but you need to understand that 32-bit OS address only 3 gigabytes of RAM, the rest, unfortunately, is inactive...

6. Now it’s the optical drive’s turn. Disconnect the two connectors and unscrew the 3 screws. Next, take out the device. Apple is using a SATA drive for the first time. Model Panasonic #UJ878A. The previous drive had an ATA (IDE) interface.

7. Take out two fans. To do this, unscrew 6 screws. Apple has long used a unique fan design with a large number of blades. This provides better cooling with low RPM. The slower the fan rotates, the less noise it makes.

8. Now we disconnect 9 cables and connectors that go to the board and unscrew 11 screws. Although it seems like there are too many screws, the previous MacBook Pro model had even more. All these screws are attached to an all-metal case, which greatly simplifies the automated assembly of a laptop in production, which suggests that the Apple Macintosh company is still very far from such monsters as Rolex or BMW :-)

9. Filming motherboard. There are obvious similarities between the motherboards of the MacBook Air, the new Macbook, and this MacBook Pro. Apple takes advantage of advances in laptop design and puts the same type of components.

10. A cooling radiator is attached to the top of the motherboard. Let's take it off.

11. The large chip on top is an Intel 2.4 Ghz Penryn processor - soldered to the mother via BGA mounting - like the north bridge and video chip. It has 3Mb L2 cache and a 1066 MHz FSB bus. The other two are chips from Nvidia. They take up most of the motherboard. There's no way either chip would fit into a MacBook Air. The first is GeForce 9400M (north bridge). The second, which is larger in size, is the GeForce 9600M GT. Has 32 cores and a capacity of 120 gigaflops (not bad for a laptop, right?)

12. We continue to disassemble the MacBook Pro. Now remove the screen cover. We unscrew the six screws next to the hinges of the laptop lid closing mechanism.

13. Unscrew the Airport board. Disconnect the antenna connector and wire. The Bluetooth cable is hidden under the screen and appears to be located between the glass and the metal body. Therefore, if you manage to damage the Bluetooth module, you will have to change the entire display! Summary: be extremely careful when disassembling Apple laptops - you don’t want to break an Acer 5100 in the basement on your knee!!!

14. Disassemble the upper part of the “unibody” housing. It houses the keyboard, glass trackpad and connecting cables. If you break a key on the keyboard, you'll have to replace the entire chassis unit in the same way, since Apple manufactures this part of the laptop as a single unit. This is where the real money comes in, if available<кривых рук> :-((((

15. To save readers money, we will try to disassemble the upper part of the case ourselves, without your participation in this expensive experiment. The keyboard is held in place with many small screws. We'll unscrew every single one of them.

16. When dismantling the keyboard, we counted 56 screws and two more on the power button. The whole procedure took 20 minutes. It seems that, in case of problems, you can fix the keyboard of this “golden laptop” yourself: the main thing is to have straight hands, spare keys, micro-lifts and extreme care when assembling/disassembling the keyboard of the Apple MacBooK pro laptop.

OK it's all over Now. Incredibly cool machine. We are still impressed by how easy it is to disassemble a Macbook Pro (and how easy it is to break it with crooked hands in the absence of certain skills).

In the photo: bottom left - hard drive and battery; on top - screen; in the center - the motherboard, fans and speakers; on right - top part cases and keyboard.

The article is based on materials from an excellent computer site

If this is your first time starting to disassemble a laptop, we recommend that you pay attention to the article “”. This article contains recommendations that will help you avoid typical mistakes in the process of disassembly.

How to clean dust from MacBook A1502

If the laptop overheats during operation and suddenly turns off, this is most likely due to overheating of the cooling system. The reason for this is the accumulation of dust on the radiator. If you do not clean the cooling system in time, this will lead to damage to the motherboard in your laptop. You can fix this problem yourself by repeating all the steps shown in the video below. The information provided in our video instructions makes it possible to clean your laptop from dust yourself at home. The necessary tools for repairs can be purchased at the end of the page.

Installing an SSD in a MacBook A1502 laptop, how to change the hard drive

Video instructions that you can use yourself replace HDD with SSD in MacBook A1502 laptop. You will also learn how to replace a faulty hard drive with a new HDD. Classic magnetic disks (HDDs) are more fragile and much slower than modern SSD drives. Consequently, replacing the HDD with an SSD will increase the speed of the laptop significantly. Our video below shows step-by-step instruction how to install an SSD in a laptop.

Reassembly of MacBook A1502

Once disassembly and repair is complete, this video will help you reassemble your laptop to its original condition.

The iFixit dismantling is always good because it allows you to visually track all the changes that the speakers talked about and the press made noise about. Having collected enough positive and negative things about the new MacBook Pro, we decided to dive into the “iron” jungle, and engineers, who constantly fly to Australia to snatch the latest releases first-hand, promptly provided a complete analysis of the MacBook Pro 13″ without Touch Bar.

The model without the new-fangled socket was chosen to be torn to pieces. Its characteristics:

• 13.3″ Retina display with IPS matrix giving a resolution of 2560 x 1600 pixels (227 ppi) with P3 color depth
• Intel Core i5 Skylake processor with a frequency of 2.0 GHz ( Turbo Boost up to 3.1 GHz) with built-in Intel Iris Graphics 540 video chip
• 8 GB RAM with a frequency of 1866 MHz LPDDR3 (16 GB can be installed)
• 256 GB, 512 GB or 1 TB SSD
• two Thunderbolt 3 (USB-C) ports with charging support, DisplayPort, Thunderbolt, USB 3.1 Gen 2
• Silver or Space Gray colors

When examining this MacBoo Pro model from all sides, nothing was found except two Thunderbolt 3 ports on the left and one lone 3.5 mm jack on the right. It turns out that the policy that Cupertino applied to the iPhone 7 does not work on Macs... not yet. I wonder if this is good or bad? :)

The A1708 assembly does not sport a touch panel with emoticons, but there is room for an unusually long mechanical Escape button. Of course, along with the rest of the functional range.

Maniacs comparing the dimensions of Apple's already thin and weightless laptops (ultrabooks) can enjoy the image above, where the new MacBook Pro 13″ is located next to just a MacBook 12″. Here, by the way, a single design trend can be clearly seen. And how striking is the twice as large trackpad!

So, enough of admiring and it’s time to move on to direct analysis, especially since the first step has not changed for 6 years. Yes, yes, the Pentalob screws on the back cover have been marinating for six years. The number “6” was also reflected in the number of fasteners, the number of which was also reduced from 8 pieces in the MacBook 2015 and from 10 pieces in most MacBook Pros.

But the back cover itself offered serious resistance, so it was necessary to use a suction cup, which has proven itself when dismantling the iPhone. You need to pick up a piece of metal and then pry it with a pick to get to the electronics.

What immediately caught my eye were the protected T5 screws, which provide solid protection for the battery pack.

Behind the hinged flap of the connector there were two small copper pads responsible for plus and minus (ground).

Then, guided by intuition, iFixit engineers carried out an easier procedure for removing the trackpad, which is no longer hidden under the battery. Behind the Force Touch, by the way, was fixed that same “magic” magnet, held solely by screws and spring connectors.

The following components are responsible for the trackpad:

• red - ST Microelectronics STM32F103VB ARM Cortex-M3 MCU chip
• orange - Broadcom BCM5976C1KUFBG touch controller

The ease with which the experts got to the trackpad was immediately counterbalanced by the copious amount of glue on the way to the battery. Old friends, a heater and a plastic spatula, came in handy again.

The lithium polymer blocks have left the sticky bath and revealed the first really important fact - a 27% reduced battery capacity. Even without looking at the specifications, where 4781 mAh is printed, the deprivations become obvious, because the MacBook Pro 13″ body has three panels instead of six.

The SSD in “camouflage” instantly attracted attention. After removing the protective tape, the PCI-e board was safely undocked, confirming the second fact - self-replaceable solid-state drives, but we remind you that you won’t be able to install any SSD, you’ll still have to fork out the cash.

A more thorough inspection of the vault revealed the manufacturer and other components. The drive was manufactured by SanDisk, now owned by Western Digital; the rest of the details are below:

• red - SanDisk SDRQKBDC4 064G 64 GB flash memory (4 pcs.)
• orange - Apple controller 338S00227
• yellow - Texas Instruments 58879D MOSFET
• green - F4432ACPE-GD-F type Micron 512 MB DDR2 RAM
• blue - sealed Apple SSD controller 338S00199

Removing the speaker traditionally could not be done with just the left hand, because it was protected by screwed gaskets to dampen the vibrations that new speakers with an improved “boom effect” would certainly produce.

Now there was nothing stopping the motherboard from being freed, where it turned out that the “improved architecture” was actually a change in the positions of the heatsink screws on the back wall.

• red – SKhynix H9CCNNNBJTML
• orange - Texas Instruments TPS51980 Buck Converter for memory power management
• yellow – Universal Scientific Industrial 339S025 Wi-Fi module
• green – Intel DSL6510 Thunderbolt 3 controller
• blue - Texas Instruments 58873D Synchronous Buck NexFET Power Block MOSFET Pair
• blue – Broadcom BCM15700A2 camera processor
• purple – Micron 512 MB DDR3L SDRAM

On the other side:

• SKhynix H9CCNNNBJTML LPDDR3 high-speed synchronous DRAM
• Texas Instruments SN650839 66AL7XWGI (as seen in the 2016 Retina MacBook)
• 2x Texas Instruments CD3215B03 66AQ8YW G1
• Winbond SpiFlash 64 Mb serial flash memory
• Texas Instruments TM4EA231 H6ZXRI system management controller
• Cirrus Logic CS42L63A Audio Codec
• Intersil 95828 HRTZ X630MRR

Now about the full-fledged survivor - a 3.5 mm jack for headphones, but as one module, to which 2 microphones are attached, stretching down to the fan.

To everyone's surprise, Apple carried over the fans from the 2012 model. Local “Carlsons” are very, very quiet thanks to the asymmetrical landing of the blades.

Just below the screen, the hardware responsible for the life of a huge number of Retina pixels was discovered:

• B1332BDPA 090BX 1605
• National Semiconductor 67A800U 49B1-04
• Texas Instruments 65CLKEI TPS65157
• NXP LPC812 ARM Cortex M0+ 32-bit MCU
• Texas Instruments TPS65158 High Resolution LCD Bias IC for TV

Apple attached the hinge protection with special love to prevent the MacBook from falling apart. This same protection plays the role of an antenna. As for how the hinge works: a spring mechanism twists the cable when the display is closed and unwinds it when opened. That is why the lid became easier to close.

The hinges are a showcase of injection molding technology: they are thin, light and strong.

And here is the second generation of the keyboard “butterfly” in all its glory. Differences include higher keycaps, which make searching for the keys more comfortable, and a dome mechanism, which is responsible for improved stability compared to regular MacBooks.

iFixit deservedly awarded the new MacBook Pro 13″ without Touch Bar a 2 out of 10 on the repairability scale, only pleased with the easily detachable trackpad. The biggest challenges were the amount of glue around the battery, the Pentalob screws, the RAM soldered to the motherboard, and the non-standard type of PCIe SSDs. In general, tuning new firmware is problematic, expensive and not at all safe.

The need to disassemble a MacBook most often arises when it breaks or the device needs to be cleaned. If the MacBook was purchased recently and is under warranty, then it is better to use the services of a service center specialist to perform the operation; however, if the manufacturer’s warranty expires, it is much cheaper and more profitable to repair the expensive MacBook yourself. It is worth noting that if the device is under warranty, even one unscrewed screw on the device body can deprive the consumer of privileges. Treat this very carefully so that there are no problems with the manufacturer in the future.

If you need to disassemble your Mac for cleaning or repair, we'll tell you how

Although the MacBook from Apple is considered a unique development in computer technology, it has a stylish design, is characterized by a very thin and original appearance, an ordinary person with even minor knowledge of the technological features of devices can disassemble and clean it.

As people say, the eyes are afraid, but the hands do. At first glance, it’s even scary to touch a fragile and delicate device again without a visible need. However, like any other computer equipment, Apple MacBooks can be disassembled using a set of tools and repair tools. The only difference is the need to purchase special screwdrivers for disassembling computer equipment and a plastic spatula, which is required for careful disassembly of the cases, since the elements in them are characterized by miniature size.

Despite the number of MacBook models produced by Apple, the technology for disassembling devices is practically no different; only elementary differences are different in the form of the number of bolts, their location and configuration.

Let's look at the technology for disassembling devices using the example of popular laptop models MacBook Pro and MacBook Air, produced in 2006 and 2008, respectively, which are prominent representatives sixth and fifth generation of the line.

How to disassemble MacBook Pro 13

To disassemble the MacBook Pro 13, you must begin by removing the bottom panel of the laptop. To do this, you need to turn the device over bottom up and unscrew the eight miniature screws that hold it in place.

After removing the cover, the owner will see the internal contents of his MacBook. Next you need to pull out the battery, to remove which you will need to unscrew two more screws. To remove them you need an unusual three-sided screwdriver. After this, you can remove the battery by first disconnecting the connector from the motherboard.

To dismantle and clean the fan, you must first remove the optical drive. Next, you need to unscrew the three screws that hold the fan in the MacBook Pro case with a regular screwdriver, after first disconnecting the wire that goes from the fan to the laptop’s motherboard. The fan needs to be cleaned very thoroughly before reinstalling it.

Next you need to disconnect the wire that goes from the monitor to the board and unscrew the seven screws securing the motherboard and two to disconnect the connector external battery. Dismantle RAM It is not required to clean the laptop, so there is no point in removing it.

Next, in order to completely disassemble the MacBook Pro 13, you will need to disconnect the cables that go to the touchpad and keyboard, and also disconnect the battery indicator. Additionally, you will have to dismantle the plastic fastening of the signal cable from the display and remove the microphone, which is located in a special recessed socket. After these operations, you can carefully and effortlessly pull out the MacBook Pro 13 motherboard. The laptop radiator and the remaining elements of the cooling system are removed along with the board. Turning the board over, you can see the heatsink itself. Disconnect it from the common unit by unscrewing the four screws.

Assembly is carried out in reverse order

At this point, disassembling the laptop can be considered complete. All that remains is to clean all the elements of the system, replace parts that have become unusable, if any, and reassemble everything in the reverse order. Experts also advise that before assembling the MacBook Pro, treat standard areas with special thermal paste, which has a beneficial effect on the laptop’s cooling system and the service life of the unit’s parts.

How to disassemble a MacBook Air

As already mentioned, disassembly different models Apple laptops have no significant differences. To disassemble the MacBook Air, as in the previous case, you must begin by removing the back panel of the device. To do this, the owner will need a rare five-sided screwdriver, with which you can unscrew the eight mounting screws.

Despite the significant similarity of the models under consideration, the internal space of the modules is significantly different. Most of the case space is occupied by a super-thin battery, which must be removed by unscrewing several screws with the same five-blade screwdriver.

The next step is to remove the speakers. The MacBook Air is equipped with powerful speakers, which must be removed using a special plastic spatula designed to work with very sensitive microelements and microcircuits.

Next, you need to sequentially remove the fan, microphone, motherboard and radiator of the laptop cooling system. Disassembling the MacBook Air is not difficult; the activity is similar to the previous option. The only difference is the need for a torx screwdriver - without it, it is almost impossible to unscrew the mounting screws on the laptop.

After cleaning the boards, laptop cooling elements and fan, all module parts are assembled in the reverse order. Assembling and disassembling a laptop is not particularly difficult; the main thing is to treat the work responsibly and not lose small parts and screws during maintenance work. For this purpose, specialists very often use magnetic boards. When you stack small metal elements on such a board, they will not get lost around the room.

After assembly, all that remains is to check the functionality of the device. If the work was done correctly, all elements are securely installed in their original places, then the laptop will function without hitches or malfunctions.

Let's sum it up

Experts advise performing preventive cleaning of your MacBook at least once a year. With contamination of the cooling system and internal microcircuits, the MacBook begins to regularly overheat, slow down and even freeze. And if during the warranty period for this procedure you just need to contact the service center and the professionals will do everything for you, then after the end of the warranty period you will have to pay a tidy sum out of your pocket for such services.

Following the recommendations in this article, a person who is related to technology and understands the technology of functioning of system elements will be able to independently, without the help of specialists, cope with the task, disassemble the device and carry out preventative cleaning of the MacBook. The main thing is to take your work responsibly - and you will succeed.

Fair, not overpriced and not underestimated. There should be prices on the Service website. Necessarily! without asterisks, clear and detailed, where technically possible - as accurate and concise as possible.

If spare parts are available, up to 85% of complex repairs can be completed in 1-2 days. Modular repairs require much less time. The website shows the approximate duration of any repair.

Warranty and responsibility

A guarantee must be given for any repairs. Everything is described on the website and in the documents. The guarantee is self-confidence and respect for you. A 3-6 month warranty is good and sufficient. It is needed to check quality and hidden defects that cannot be detected immediately. You see honest and realistic terms (not 3 years), you can be sure that they will help you.

Half the battle is Apple repair- this is the quality and reliability of spare parts, so a good service works with suppliers directly, there are always several reliable channels and your own warehouse with proven spare parts for current models, so that you do not have to waste extra time.

Free diagnostics

This is very important and has already become a rule of good manners for the service center. Diagnostics is the most difficult and important part of the repair, but you don't have to pay a penny for it, even if you don't repair the device based on its results.

Service repairs and delivery

Good service We value your time, which is why we offer free shipping. And for the same reason, repairs are carried out only in the workshop of a service center: they can be done correctly and according to technology only in a prepared place.

Convenient schedule

If the Service works for you, and not for itself, then it is always open! absolutely. The schedule should be convenient to fit in before and after work. Good service works on weekends and holidays. We are waiting for you and working on your devices every day: 9:00 - 21:00

The reputation of professionals consists of several points

Company age and experience

Reliable and experienced service has been known for a long time.
If a company has been on the market for many years and has managed to establish itself as an expert, people turn to it, write about it, and recommend it. We know what we are talking about, since 98% of incoming devices in the service center are restored.
Other service centers trust us and refer complex cases to us.

How many masters in areas

If there are always several engineers waiting for you for each type of equipment, you can be sure:
1. there will be no queue (or it will be minimal) - your device will be taken care of right away.
2. you give your Macbook for repair to an expert in the field of Mac repairs. He knows all the secrets of these devices

Technical literacy

If you ask a question, a specialist should answer it as accurately as possible.
So that you can imagine what exactly you need.
They will try to solve the problem. In most cases, from the description you can understand what happened and how to fix the problem.