How to use the universal TV remote control. How to choose and set up a universal remote control for a TV - setup methods and control options. Important information about the remote control

Methods on how to set up a universal remote control for a TV are easy to perform and are not difficult even for a beginner. Despite the variety of models, there are only 4 ways to program the device. A dozen remotes in the house are an old way to control equipment. It is more convenient to make one universal and teach households to use it.

The principle of operation and purpose of the universal remote control

The principle of operation of the remote control remote control) is to control household appliances using infrared radiation. Inside the device is a circuit that is programmed using settings and codes to a sensor in a device, such as a set-top box, TV, music center, and so on.

From the sensor on the device, information in the form of vibrations is transmitted to the same sensor in technology. Externally, the control panel almost does not differ from the standard ones. The same buttons: Source, Mute, Set, Power, volume control, channel switching.

It can be programmed to control the TV and change channels. If the house has an air conditioner, a music center, a receiver, an electric oven or an extractor hood, and they have a remote control function, it is worth using ways to reprogram the remote control and synchronize it with the equipment.

Instructions on how to connect to the device

Method 1

• Turn on and direct to the screen.
• Hold OK, TV or Set for 5 seconds.
• If the indicator blinked and went out, the device was successfully tied.
• Continued blinking: enter the code corresponding to the device on the remote control.
• Press TV. If after setting the TV does not respond to the remote control signal, the code is entered with an error. It is recommended to repeat again.

The equipment has types of batteries: AAA type, round batteries for kitchen scales and clocks, and which are charged with electricity.

Method 2

If the remote still does not see the TV, it is advisable to activate the operation of the equipment in a different way:

• Hold down SET or TV until the lamp on the remote control lights up.
• Click POWER.
• Enter the device code. The indicator light will turn off.
• Press MULT or OK if the diode on the remote does not go out.

Method 3

Hold two buttons: SET (TV) and POWER. Enter the code at the same time.

Be sure to check: the remote control must regulate the device in accordance with the keys. If the TV mistakenly interprets the device, the remote does not work correctly and the settings should be reflashed again.

Setup without code

Unlock missing devices connection:

1. Turn on the TV on any channel.
2. Hold TV and SET at the same time.
3. The diode next to POWER lights up.
4. Now you need to quickly press POWER many times. Do before programming the remote and TV.
5. Finish setting - SET or TV.
   Household appliances are tuned to DPU, like TVs.

How to find out the code

Each device has codes to flash the equipment pairing. For example, the code BBK is 0743, 0983, 1313 or 1873. You can find out the password in the instructions for the device. Sometimes such a document is present in the box to the universal device. For example, the rolsen TV remote control, universal for any brand of equipment, contains a booklet with company codes in alphabetical order.

Most brands: Gal Lm P001, Dexp, Changer Tv, Chunghop, Vix, Gal lm P003, Jumbo Universal Remote, Ritmix Rds Remote, Irc contain tables of codes for equipment and detailed instructions in Russian, which will allow you to recode the firmware access to the equipment.

Code table for different TV brands

Smartphones with the universal remote control function

Applications for phones with remote control (remote control) allow you to replace the remote mobile device. In this case, the main thing is the compatibility of software versions.

To understand how to use these softwares, you need to download and follow the manual. Applications are intuitive to the average person. They are equipped with icons with household appliances and numerous functions.

Application List:

These products are downloaded online via App Store or Google Play.

Useful video

Random joke:

Setting up the Beeline universal remote control

Detailed instructions for setting up Beeline universal remotes with the Setup button. For simplified instructions, see the main page.

By default, Beeline universal remotes are configured for Motorola set-top boxes. But there are many other models and it’s not a fact that you will get the Motorolka. If you brought another set-top box ("Pussy" (Cisco) for example), you must first bind it to the remote control, otherwise nothing will work. A valiant bee installer MUST set up the remote, but as practice shows, he often simply does not have enough time for this (don't blame the poor guy, they are already driven like dogs), or you decide to do everything yourself. It is for such cases that this article is written.

× Attention 1!

Follow the instructions carefully. If you think too long and do not enter the code for 4 or more seconds, the remote control goes into normal standby mode. If you suddenly did something wrong, don't worry, you just need to. More on this at the end of the article.

× Attention 2!

This article fully applies to Beeline universal remotes of the new model. It is easy to distinguish by appearance- the remote control is always black, as in the figures shown, the "Beeline" logo is applied at the bottom, the button " SETUP" located at the top of the remote control under the " MENU".
In extremely rare cases, you may come across an outdated AT6400 control panel without a " SETUP", or MXv3 models with the " key Learn" instead of " SETUP". The color of such a remote control can be either black or light. It is easy to determine the binding of the remote control to the model - at the bottom of the remote control in place of the logo " Beeline"STB logo will be located" Cisco"or" Motorola".
The remotes of this series are tied only to their set-top box and will not control another (i.e. the remote with the "Motorola" logo will not work with the prefix "Kisco" and vice versa). But you can still set it up to control the on/off and volume of your TV. A detailed article about such remotes can be found here:

× Supplement 2017

From the new (2017) year, Beeline began to install new generation set-top boxes - Jupiter. Of the advantages of this miracle - a huge terabyte screw, of the obvious disadvantages - the firmware for them is still damp. Very. Plus, only your own remote control is required for it, the usual universal one will not work. Link below complete instruction to set up these devices:

Setting sequence:

Unlike its predecessors, Beeline universal remotes of the new model (with a setup button) are extremely simple and reliable in setting up. With strict observance of the instructions, setting up and binding such remotes does not cause any difficulties. So let's get started:

tie to pussy(Cisco):

1. Turn on the TV! ;)
2. Press and release the button STB.
3. Press the buttons SIMULTANEOUSLY SETUP And C, WAIT!
4. When the button STB SETUP And C.
5. We use :)

We bind to Motorola(Motorola):

1. Turn on the TV! ;)
2. Press and release the button STB.
3. Press the buttons SIMULTANEOUSLY SETUP And B, WAIT!
4. When the button STB flashes twice, release the buttons SETUP And B.
5. Press the volume button (not necessary, for verification).
6. We use :)

We bind to Tatung(Tatung):

1. Turn on the TV! ;)
2. Press and release the button STB.
3. Press the buttons SIMULTANEOUSLY SETUP And A, WAIT!
4. When the button STB flashes twice, release the buttons SETUP And A.
5. Press the volume button (not necessary, for verification).
6. We use :)

How to bind the volume control key to the TV:

1. Turn on the TV!
2. Point the remote at the TV.
3. Push button SETUP, WAIT.
4. When the button STB flashes twice, let go SETUP.
5. Press and release the button TV.
6. Make sure the button TV blinked 2 times.
7. enjoy.

× I'll clarify to remove possible questions.
By default, the universal remote controls the volume of the SET-TO-BOX (when the key is active). STB). The active key is very easy to determine, it flashes briefly when you press any button on the remote control. Now, after our gestures, the remote control can also control TV. But for this to happen, you need to activate the mode TV by clicking on TV. After adjusting the volume and other settings of the TV, you need to press again on STB to return to the control mode of the Beeline prefix.
It seems obvious, but very often people just forget to switch modes. TV/STB and are at a loss as to why the remote does not work :).

How to bind the volume control key to the Beeline prefix:

By default, the volume key on the universal remote control is always tied to the set-top box, but just in case :-)

1. Push button SETUP, WAIT.
2. When the button STB flashes twice, let go SETUP.
3. Press the volume up button.
4. Press and release the button STB.
5. Make sure the button STB blinked 2 times.
6. enjoy.

Automatic setting of the remote control for full control of TV / DVD:

If you want to not only control the volume of your TV or DVD set-top box, but also enter the native service menu using a universal remote control, you need to “acquaint” them, i.e. "attach" the universal remote to a TV or DVD. After this operation, the native remote control from the TV becomes, as a rule, not needed at all.

1. Turn on the TV or DVD!
2. Press and release the button TV for TV, DVD for DVD.
3. Point the remote at the TV or DVD.
4. Push button OK(in the center of the console), WAIT.
5. It will automatically search for control codes for your device. During the entire process, keep the remote control in the field of view of the device! When the process ends, the device (TV or DVD) will turn off.
6. Release button OK.
7. enjoy.

Manual setting of the remote for full control of TV / DVD:

There are two ways to bind the remote - manual and automatic. I recommend using automatic - both easier and more reliable. If the automatic search did not give results (which happens very rarely), you can use the code table. Look for your device in the table and enter the code (4 digits)

1. Turn on the TV or other device - TV- TV, DVD- DVD set-top box AUX- amplifiers, video recorders, etc.
2. Point the remote at the selected device.
3. Push button SETUP, WAIT.
4. When the button of the selected device blinks twice, release SETUP.
5. Enter the device code from the code table.
We take the codes from the instructions here:

6. If the code is successfully entered, the button of the device being configured will blink twice.

If the code is not received for more than 4 seconds, the remote control will return to standby mode. In this case, repeat the procedure from point 2.

7. enjoy.

Reset to factory settings:

If something went wrong, or you are "too smart" with the settings, you can always reset the remote to factory settings. But keep in mind that in this case, the universal remote control will be set to the prefix "Motorola" by default. If your set-top box is of a different model, you will need to reconfigure the remote to it. So reset:

1. Press and release the button STB.
2. Push button SETUP, WAIT until it flashes 2 times, release the button SETUP.
3. Press the buttons one by one 9, 7, 7 .
4. Button STB flashes four times, signaling that the remote control has returned to its default settings.

(Hover your mouse over the image to enlarge it)

Instructions for setting up a universal remote control in PDF from Beeline:

And finally, instructions for setting up the Beeline universal remote control in PDF from Beeline itself.

Turn on the device you will control. Brand code search is only supported by older TVs, DVD players, VCRs and satellite receivers. It is not supported on stereos, DVRs, and HDTVs (for those devices, use the different method described in this article).

• The brand code can be found in the documentation for the remote control or on this site.

Today, the multifunctional remote control is very popular and in demand among a large number of people, because it allows you to control various models, which is very convenient and practical. Now there is no need to have several different control panels when there are several TVs of various types in the house. It is enough to have only one, with which you can easily and simply manage any model. Now, there are a significant number of different models on sale, and each of them has its own set-up features that must be correctly performed. In the modern electronics market, anyone has a great opportunity to purchase a relatively inexpensive multifunctional device with which you can easily control several television receivers. This opportunity is provided by special codes for universal remotes for tv.

Setting method

When your device does not have a special key on which "SET" is written, then you have it multifunctional and can be tuned to a TV, a modern dvd player, etc. In this case, you will need to press a special button with the name "SET" and any other available on the control device. For example, when you make a connection, then you need to press the button with the name "TV" and the off key, then the installed indicator will light up and you will need to enter a special code for a certain type of device.

Codes:

Player "BBK" - 0743, 0983, 1313, 1873.
"Daewoo" - 0021, 2531, 2581, 0061, 0661, 0861, 0931, 1111, 2051, 0081, 0351, 1211, 1811, 1931, 1891, 2411.
"JVC" - 0051, 0171, 0821, 1031, 1181, 0641, 1451, 0301, 1261, 0351.
"NEC" - 0021, 0031, 0261, 0081, 0661, 0751, 0051, 0861, 1281, 0421, 0531, 0931, 2481, 0061, 1211, 1321, 1561, 2031.
"Goldstar" - 0001, 0211, 0281, 0021, 2051, 0081, 0061, 0311, 1191, 0501, 1371, 0071, 0431, 0651, 1351, 1341, 2591, 0931, 1031, 0231
"LG" - 0001, 0021, 0081, 2591, 1031, 1351, 2051, 0501, 0211, 1341, 1191, 1371, 0431, 0061, 0071, 0231, 0281, 0311, 0651, 0931.
"Philips" - 0021, 0151, 1021, 0931, 1391, 0061, 0291, 0301, 0331, 0391, 0661, 1401, 1571, 1081, 2511.
Hitachi 0861, 0971, 0981, 1381, 1891, 2041, 1491, 2001, 1111, 1671, 2391, 0911, 2451, 1991, 2211.
"Panasonic" - 0001, 0061, 0201, 0231, 0371, 0311, 0631, 1611, 0911, 0931, 1161, 1841, 1861, 2361, 2461.
"Samsung" - 0021, 0061, 0101, 0121, 0081, 0471, 0501, 1371, 0801, 0931, 0171, 0231, 0341, 0281, 2051, 1281, 1041, 1061, 1131, 2121.
"Sharp" - 0051, 0171, 0221, 0301, 0331, 0451, 0831, 1611, 1181, 1551, 1951, 2081, 2371.
"Sony" - 0031, 0051, 0061, 0191, 0221, 0611, 0931, 1791, 1981, 2401, 2471, 2331.
"Thomson" - 0061, 0441, 0591, 0931, 0961, 0211, 0491, 1061.

This device is very convenient and quite practical to use, but before that they need to be configured as correctly as possible. For customization, you can use the information provided above.

TV remote control (RC)- a device that is used daily. Not surprisingly, the life of the remote control may be too short. But what to do if it breaks? This is where the universal remote control comes in handy. Its setup will not take much time and effort.

First you need to figure out which model of the universal remote control is suitable for your TV. As a rule, most remotes are suitable, but their operation may be slightly incorrect. That is, some buttons may not perform their function, for example, the volume button can switch channels, and the TV off button can mute the sound. But in any case, it will be more convenient than going to the TV and switching channels manually.

How to set up a TV remote

There are quite a few ways to set up a universal remote control for a TV, it’s unrealistic to write about all of them. Consider the most common:

Quick setup of the remote control for the TV;
Setting according to the instructions;
Seller setup.

Quick Setup is the easiest way. With this method, the remote control must have the inscriptions of the manufacturer of your equipment. We turn off all electronic equipment that has a remote control from the network, except for the custom one. Turn on TV, on the universal remote control, press the appropriate button (brand TV) and hold. You need to hold the button until the TV gives any sign. It can turn off, switch to another mode, turn off the sound, add sound, etc. It is at this point that the settings button must be released. It may not work the first time, as the interval is very short. The universal remote control is configured.

Second way more complicated. The universal remote control comes with setup instructions. She will need it. In the book for setting up the remote control, the codes for setting up will be presented. Find the make and model of your TV there. Several codes can be used for one TV model, so if the first one does not fit, do not be discouraged.
Next, turn on the TV, point the universal remote control at it and press two buttons- "SET" (or "TV") and on / off. TV. We dial the code of our TV, the light on the remote control should go out. Setup completed.

Third way simplest. If you buy a universal remote control for a TV in electronics hypermarkets, you can ask the seller to set it up right away. To do this, do not forget to write down the model of your TV on a piece of paper, or take a picture.

Where to buy a TV remote

The sale of TV remote controls is organized both in electronics hypermarkets and on the Internet. Also, the remote control can be purchased at the official service centers of the manufacturer of your equipment. And of course, you can buy a universal remote control in China -.

Remote control DVB-T2 universal

More recently, a universal remote control for DVB-T2 set-top boxes has appeared on sale - HUAYU DVB-T2. This model is compatible with 95% of receivers for receiving digital terrestrial television sold in the territory of the Russian Federation. The remote control is configured either automatically or by entering the desired code.

The HUAYU DVB-T2 universal remote control has an affordable price. The package includes the HUAYU DVB-T2 universal remote control itself, instructions with codes.

Partial list of compatible devices: D-color DC711HD, D-Color DC1001HD, D-Color DC901HD, D-Color DC910HD, D-Color DC921HD, D-Color DC1201HD, D-Color DC1301HD, D-Color DC1302HD, D-Color DC1401HD, DELTA SYSTEMS DS-100HD, KASKAD VA-2102HD, SELENGA T2-1000, GOLDSTAR GS8833HD, ROSS&MOOR RMR-818T2 HD, HUBA HB-9816, Globo GL60, GLOBO E-RCU-018, Hyundai H-DVB03T2, Iconbit HDR21, Supra SDT -92, Telant, World Vision T34, EVO-01NEW, Golden Media Mania 3 HD, Lumax DVT2-4110HD, Mystery MMP-70DT2, MYSTERY MMP-80DT, MMP-75DT2, MMP-85DT2, Openbox T2-02 HD, Prology DVT -100, Zala 1, Rainbow (world vision) s517ir, BBK RC-STB100, GoldMaster T-707HD, Oriel 810, Sharp GB0 12WJSA, Sharp GB0 13WJSA, SkyTech 57 G, World Vision T40, BBK RC-SMP712, Energy EVO- 1, General Satellite TE-8714, Lans DTR-100, Oriel 790, Lumax DV-2500CA, SELENGA T90, HD900, HD910, Hyundai DVB01T2, Oriel 710, Oriel ver.5, Rostelecom SML-292 HD, Divisat DVS HD-600T2 , Polar DT-1002, Oriel ver. 10, MTS WS-28A, Kaskad DVBT-2, REXANT RX-511, Rolsen RDB-502, Globo GL50, Rexant GL50, AirTone DB 2206, Home BY-628 DVB, TVjet RE820HDT2, TVjet RE820HDT2 option 2 POWER+GOTO, SIGNAL HD-200, HD-100 - POWER + 4, SELENGA T90, HD900, HD910, HD920 - POWER + FAV, D-COLOR DC1002HD MINI POWER+SUB-T, CADENA ST-203AF POWER+1 , BOOOX T2 UNIVERSAL POWER+1 , REFLECT DIGITAL, COMPACT POWER.